How-to

Ground support equipment tablet mounts: RAM for tugs and forklifts

Choose and fit RAM Mounts docks, holders and bases for Zebra handhelds, scanner guns and rugged tablets on airport tugs, baggage tractors, belt loaders, de-icing trucks and cargo forklifts.

60 min Difficulty: Medium Updated: By SCANSHOP team
In this guide

    A ground support equipment tablet mount must cope with vibration, rain, frost, gloved hands and open cabs, and still keep the device charged and in place. This guide covers RAM Mounts docks, holders and bases for Zebra handhelds, scanner guns and rugged tablets on airport tugs, baggage tractors, belt loaders, de-icing trucks and cargo forklifts.

    SCANSHOP is an official RAM Mounts reseller. For tablets in the cockpit, see our RAM aviation EFB tablet mounts guide.

    RAM Mounts logo

    Before you start

    You'll need
    • The device model and its boot, frame or IntelliSkin sleeve
    • The cab type (open or closed) and a solid mounting point
    • The voltage of the vehicle's accessory supply
    • Your needs for charging, USB and locking

    Map the vehicle: cab, mounting point and view

    Find a spot the operator can reach and read easily. In open cabs, as on many baggage tractors and forklifts, the device takes rain, cold and every bump: choose a dock that holds it firmly and locks. Keep the view ahead and to the load, the controls and the steps clear.

    Check

    RAM: "Do not install this product near or over an airbag deployment area or in a location that obstructs the driver's vision or interferes with vehicle operation." Follow the vehicle maker's and RAM's instructions.

    1234567
    1 Roll bar · 2 Tool-free clamp · 3 Short arm · 4 Locking dock with handheld · 5 Hardwire charger · 6 Fuse · 7 Operator's view: keep clear

    Choose the Zebra handheld and scanner vehicle mount

    Zebra lists "Airlines (under wing)" among the TC73/TC78's markets; both are rated IP65 and IP68 with battery and take "bare or gloved fingertip input". RAM's matching docks and holders:

    Device RAM product Power Lock
    TC73, TC78 in IntelliSkin Next Gen GDS Locking Dock, heated pins USB-C Key
    TC22, TC27, TC53, TC58 in IntelliSkin GDS Locking Dock for TC2x/TC5x USB-C Key
    MC9300, MC9400 Locking Powered Dock, heated pins 5.5 mm DC Key
    MC9400 and other scanner guns Power-Grip XL holder None None

    The GDS docks work one-handed and leave the buttons and scanner usable. On the heated-pin docks, RAM says heating elements "prevent pogo pins from locking up" in "wet and freezing environments" (no temperature given). The Power-Grip XL is, per RAM, compatible "with a full range of ball and socket forklift mounting systems".

    Important

    RAM: "GDS Uni-Conn Snap-In docks are not recommended for open cockpit applications, such as forklifts." On open tugs, use the form-fit docks above.

    Zebra rugged handheld lifted out of a RAM Mounts GDS dock on a mesh cage, and a ground handler in a hi-vis vest scanning a baggage tag
    A Zebra handheld in a RAM GDS dock, and a baggage tag being scanned. Photo: RAM Mounts

    Video: RAM Mounts

    Choose the ground support equipment tablet mount

    For an 8" Zebra ET4x or ET401, our first choice as a tug or forklift tablet mount is the Locking Tough-Dock. RAM states it is "MIL-STD 810G Shock and Vibration tested" (for this dock only). It has a key lock, a 5.5 mm DC input and two USB-A ports for peripherals, and fits C- and D-size bases. It takes the ET4x 8" in its Rugged Frame or the ET401 8" in a RAM Skin, not IntelliSkin. Zebra says the ET401 touchscreen works with gloved fingers "even in heavy rain" (ET401 setup guide). For other tablets, see rugged tablet vehicle mounts.

    Worker placing a rugged tablet into a RAM Mounts dock hung from a forklift overhead guard on a RAM arm
    A rugged tablet going into a RAM dock on a forklift's overhead guard. Photo: RAM Mounts

    Video: RAM Mounts

    Recommended RAM docks and holders for ground support equipment

    RAM Mounts GDS key-locking powered dock with USB-A and heated pins for Zebra TC73 and TC78 in IntelliSkin – product photo
    RAM MOUNTRAM Mounts GDS Locking Powered Dock with USB-A and Heated Pins for Zebra TC73/TC78Part no. RAM-GDS-DOCKL-V12-ZE35CPDHU
    1.778,00 zł+VATIn stock
    RAM Mounts Power-Grip XL universal scanner gun holder – main product photo
    RAM MOUNTRAM Mounts Power-Grip XL Universal Scanner Gun HolderPart no. RAP-450U
    292,00 zł+VATAvailable on request

    Buying for a fleet or a tender? Ask us for a quote.

    Get a quote

    Plan charging for cold and wet shifts

    Match the charger to the dock and the vehicle:

    • USB-C GDS docks: the 10–30 V GDS hardwire charger supplies USB-C Power Delivery (5–15 V, 3 A max); for 30–64 V supplies, use the 30–64 V version.
    • 5.5 mm DC docks (ET4x Tough-Dock, MC9400 dock): RAM's DC-plug chargers differ in output voltage. Send us the dock's part number and we'll check which charger RAM lists for it.

    RAM's compatibility guide: fuel-powered trucks and propane forklifts typically work with ~10–32 V chargers; electric forklifts require a higher input range, ~24–64 V. For electric tugs, check the accessory voltage in the vehicle documentation. More in our GDS hardwire charger guide.

    Note

    RAM rates the USB-C GDS chargers for −20 °C to +70 °C, but Zebra's charging ranges are narrower: 5–40 °C for the TC22/TC27, 0–40 °C for the ET401. A frozen device may not charge, and RAM doesn't say heated pins warm it. In winter, prefer heated cabs and swap batteries indoors (TC73/TC78: Warm or Hot Swap, per Zebra).

    Pick the base: roll bar, post or overhead guard

    Mounting point RAM base Notes
    Roll bar or rail: round, square or odd-shaped Tough-Claw Medium, C Tool-less; 1"–1.875" (≈25–48 mm) round, up to 1.6" (≈41 mm) flat
    Square post up to 4" (≈102 mm) Square Post Clamp Base, D RAM: "ideal for forklift mounting"
    Overhead guard or lift cage Lift Truck Overhead Guard Base Steel plates that carry C or D ball bases; no load figure published
    Dashboard in a closed cab Round plate with ball, D Drill-down
    Crown truck with a Crown Work Assist clamp Crown Work Assist ball base, D Only for Crown Work Assist clamp accessories; clamp not included

    We use C size for handheld docks, D for tablet docks and scanner holders. RAM's approximate maximum load is 4 lb (≈1.8 kg) for C and 6 lb (≈2.7 kg) for D: "Approximate capacity for a standard ball with a mid-length arm. Shorter arms and steel-reinforced posts increase real-world capacity." Use the shortest arm that reaches, such as the D-size short arm (≈130 mm); see our RAM ball sizes guide.

    Typical builds: handheld dock + C diamond ball base + C arm + Tough-Claw; tablet dock or Power-Grip XL + D round AMPS plate + D arm + post clamp or guard plates.

    123456788
    1 Round tube · 2 Tool-free clamp · 3 Square post · 4 Post clamp · 5 Overhead guard bars · 6 Bolted steel plates · 7 C ball · 8 D ball

    Recommended RAM bases and charging for tugs and forklifts

    Buying for a fleet or a tender? Ask us for a quote.

    Get a quote

    Install, lock and check the mount

    1. Check the position with the operator seated: view, controls, steps and airbag labels.
    2. Fit the base as RAM's instructions describe. On a forklift, follow the truck maker's rules for the overhead guard.
    3. Have a qualified installer hardwire the charger, fused per the vehicle maker's and RAM's instructions (RAM gives no fuse rating for the USB-C chargers), on a battery feed (always on) or the cab fuse block (on ignition).
    4. Route cables clear of moving parts, hot surfaces and sharp edges.
    5. Lock the dock, and fit a Pin-Lock security nut to D-size arms; see our RAM locking guide.
    6. Test docking with gloves on, and check the knobs again after the first shifts.

    Equipping a fleet? Send us the devices, vehicle types and voltages, and we'll prepare a RAM parts list and quote.

    Frequently asked questions

    What is the best airport tug tablet mount for an open cab?

    A key-locking form-fit dock, such as the Locking Tough-Dock for the Zebra ET4x 8", on a short D-size arm and a post clamp or overhead-guard base. RAM does not recommend GDS Uni-Conn snap-in docks for open cockpits.

    How do I mount a Zebra MC9400 scanner on a forklift?

    Put the Power-Grip XL holder (RAP-450U) on a D-size round AMPS plate, arm and a square post clamp or overhead guard base. RAM also makes locking MC9400 docks.

    Will a Zebra handheld charge in a vehicle dock below freezing?

    Often not. RAM's USB-C GDS chargers are rated down to −20 °C, but Zebra's charging ranges start at 0 °C or 5 °C, depending on the model.

    Does the RAM Crown ball base fit any forklift?

    No. RAM-D-202U-CRO1 fits Crown Work Assist clamp accessories only, and the clamp is not included.

    Was this guide helpful?

    Used in this guide

    Compatible consumables and accessories for the Zebra ET40.

    Products used in this guide

    More Zebra ET40 guides

    Still stuck?

    Send us your model and a short description of the problem. Our team will help you find a solution.

    Contact support
    RAM Mounts Locking Tough-Dock with Power + Dual USB for Zebra ET4x 8" with Rugged Frame (RAM-HOL-ZE20PD2KLU)1.599,00 zł+VAT View product